:: Bersa Talk ::

What does de-horning mean exactly? Is it recommended? Does it affect warranty?

---

God bless America. And save it from the Dems.

Kimber Pro-carry II - 0.45.
Glock17.
Bersa Thunder 380.
Remington 597
NRA Member

All the sharp edges are rounded and smoothed out.  I don't think it's possible on the aluminum framed pistols.  I also think it would be difficult to do the slides for much of the Thunder line since the slides would have to be re-nickel plated or re-coated with whatever the coating is on the matte and duo-tone versions.

Bronson

---

"Each new generation born is in effect an invasion of civilization by little barbarians, who must be civilized before it is too late." T. Sowell.
-------------------------------------------------------------
Bersa Thunder .380
Browning HiPower
Kahr CW40
Kel-Tec P-32
Ruger Mark I
Ruger GP100

Thanks Bronson

---

God bless America. And save it from the Dems.

Kimber Pro-carry II - 0.45.
Glock17.
Bersa Thunder 380.
Remington 597
NRA Member

Thank god you answered Bronson. I was about to go into what it ment to get dehorned back in the old days. 

---

Whining is for little girls, babies, mommy’s boys and girly men.
SNIVELING? Now that’s an art form!

FS22
BT380dlx; P3AT; PPK
Beretta 92FS; CX4 Storm
BT45 UC; FS 1911 DLX; Colt M1991A1; DW Bobtail
Taurus 38UL
CZ fnh Modell 27 WWII Luftwaffe issued to Hauptman Jaeduvel
+ old family guns

I've used a Dremel tool with a rubber polishing wheel in the past with good results.  It gets rid of burrs, sharp edges, and smoothes out loading ramps and linkages.  I don't think it would void your warranty.

---

"A strong body makes the mind strong. As to the species of exercises, I advise the gun. While this gives moderate exercise to the body, it gives boldness, enterprise and independence to the mind. Let your gun therefore be the constant companion of your walks." Thomas Jefferson

Just be advised that the frames on the Thunder line are anodized aluminum.  Once you compromise the anodizing you have bare aluminum exposed to the elements and that means corrosion.

Bronson

---

"Each new generation born is in effect an invasion of civilization by little barbarians, who must be civilized before it is too late." T. Sowell.
-------------------------------------------------------------
Bersa Thunder .380
Browning HiPower
Kahr CW40
Kel-Tec P-32
Ruger Mark I
Ruger GP100

Don't touch feed ramp on Bersa with anything other than  bullets . Their ok .

Take dremel out to drive way and run over 3 or 4 times make sure really crushed. Been more guns runined  by dremel and home gunsmithing . 1911's worst for this. In case of those I think owner should have wire brush and dremel running max shove up  their .................. 

---

Bersa Thunder,
PPK/S,
1990 Colt Mustang,
380 Kel Tec
380's Rule

"Just say "Lay A Way"

"WWJBD" What Would James Bond Do?

"Hokey religions and plastic glocks are no match for a good 1911 at your side, kid."

NO !!!   Don't run over them in the driveway......just pack them up and send them to me. I can use them for carving in antler and such. They can be very destructive sometimes. Even bite occasionally.

I use my dremel to shave... and some lite dental work!

---

Whining is for little girls, babies, mommy’s boys and girly men.
SNIVELING? Now that’s an art form!

FS22
BT380dlx; P3AT; PPK
Beretta 92FS; CX4 Storm
BT45 UC; FS 1911 DLX; Colt M1991A1; DW Bobtail
Taurus 38UL
CZ fnh Modell 27 WWII Luftwaffe issued to Hauptman Jaeduvel
+ old family guns